GRC水泥構件具體是怎樣安裝的？接縫之間應該如何進行處理？GRC構件如何看起來像一體成型的？相信這些都是很多消費者比較關心的問題，下面就由
山東GRC構件小編來為大家詳細介紹一下吧。
How are GRC cement components installed? How should the joints be treated? How does the GRC component look like one piece? I believe these are the concerns of many consumers. Let's introduce them in detail by Shandong GRC component editor.
1、在安裝前要確定好安裝位置，畫好基準線。再按照基準線進行安裝，注意調整水平度和垂直度。
1. Before installation, determine the installation position and draw the reference line. Then install according to the reference line, and pay attention to adjust the levelness and verticality.
2、GRC窗套安裝：將窗套線沿著窗框外的墻體安裝，注意漲栓緊固位置要避開抹灰層。豎向窗邊線或柱子安裝到每一樓層標高時，要注意調整垂直誤差。標高誤差控制在3mm以?xún)?nèi)。
2. GRC window sleeve installation: install the window sleeve line along the wall outside the window frame, and pay attention to the fastening position of the expansion bolt to avoid the plastering layer. When the vertical window sideline or column is installed to the elevation of each floor, pay attention to adjusting the vertical error. The elevation error shall be controlled within 3mm.
3、GRC內有鋼骨架橫向構件，安裝前先在墻體上固定角碼或角鋼，作為與鋼骨架的焊接點。所有焊接點焊縫寬度不少于5mm，長度不少于連接筋直徑的4倍，全部焊渣。構件的焊接點均應涂紅丹防銹漆打底面涂銀色油漆。
3. There are cross members of steel framework in GRC. Before installation, the corner or angle steel shall be fixed on the wall as the welding point with the steel framework. The weld width of all welding points shall not be less than 5mm, and the length shall not be less than 4 times of the diameter of the connecting bar. All welding slag shall be removed. The welding points of the components shall be painted with red lead antirust paint and the bottom surface shall be painted with silver paint.
構件斷面尺寸大于300mm小于1000mm（沒有鋼骨架的）的安裝時，在保溫層上劃出埋件位置，角磨機切開保溫，用漲栓將GRC水泥構件預埋鍍鋅埋件與墻體緊固，做好節點防腐處理，修補接縫。
For the installation of components with section size greater than 300mm but less than 1000mm (without steel framework), mark the position of embedded parts on the insulation layer, cut the angle grinder for insulation, fasten the embedded galvanized parts of GRC cement components with the wall with expansion bolts, carry out node anti-corrosion treatment and repair the joints.
斷面尺寸小于300mm的構件，直接用加長漲栓穿過保溫層緊固到墻體上，注意保證螺栓的錨固長度。
Members with section size less than 300mm shall be directly fastened to the wall through the insulation layer with extended expansion bolts, and attention shall be paid to ensuring the anchorage length of bolts.
4、GRC構件與構件之間的接縫處理：GRC水泥構件外表的接縫，應平整、光滑。使用專用修補材料填充縫隙或進行回填。回填的目的是把GRC構件與主體連接成一個整體，防止與主體間的接縫開裂。
4. Joint treatment between GRC members: the joints on the surface of GRC cement members shall be flat and smooth. Fill gaps or backfill with special repair materials. The purpose of backfilling is to connect the GRC members and the main body into a whole and prevent the joints between the GRC members and the main body from cracking.
另外，回填時，須對回填面的所有廢渣雜物干凈，淋透水后才能回填，并用鋼筋或竹竿翻插回填料使其密實，不能有空殼。
In addition, during backfilling, all waste residues and sundries on the backfilling surface shall be removed, and backfilling can be carried out only after being soaked, and the backfill shall be turned over with steel bars or bamboo poles to make it dense without empty shells.
大飾線回填料需使用陶粒混凝土或膨脹珍珠巖做底層GRC填充料，應馬上處理好回填構件的結合縫。飾線、柱頂?shù)葮?gòu)件的回填面還須按8%找坡水泥膏壓光，做到光滑不能有積水。
Ceramsite concrete or expanded perlite shall be used as the bottom GRC filling material for the backfill of large decorative line, and the joint of backfill components shall be treated immediately. The backfill surface of the trim line, column top and other components shall also be calendered with 8% slope making cement paste to ensure smoothness and no water accumulation.
5、GRC收口部位的處理，如對女兒墻壓頂、窗臺板、窗下墻等部位，要做到美觀、防水，嚴格按照工藝施工（由土建施工單位做泛水）。
5. The treatment of GRC closing parts, such as the parapet coping, window sill plate, window lower wall and other parts, shall be beautiful and waterproof, and shall be constructed in strict accordance with the process (the civil construction unit shall perform flashing).
清潔收尾是工程竣工驗收前的一道工序，雖然安裝已完工，但為保證飾面質量，此工序更不能馬虎。并在全過程中注意成品保護，以便進入下道表面噴涂施工。更多相關事項就來我們網站
http://m.4spilates.com咨詢了解吧。
Cleaning and finishing is a process before the completion acceptance of the project. Although the installation has been completed, this process can not be sloppy to ensure the quality of the finish. And pay attention to the protection of finished products during the whole process, so as to enter the next surface spraying construction. For more information, please visit our website http://m.4spilates.com Consult and understand.
